Loading... Please wait...


Repairing a bad connector on the Reention Dorado downtube battery.


The Reention Dorado removeable downtube battery system is used on many brands of e-bikes including Hilleater, Juiced, surface 604, Volt bike, Smartmotion and Bitrix to name a few. With the Hilleater bikes we have seen no issues with this connection, but as the battery cases have grown bigger and motors more powerful, it can put a strain on the electrical connectors in this system and eventually the connection can become intermittent, or stop working altogether.

If the power cuts out when you go over a bump, or you have to strap the battery on with Velcro in order for it to work, you may have a bad connection at the battery. The first step in finding out of your bike has this problem is to inspect the connectors on the bike and battery.  The metal pins and sockets that make the electrical connection should be look perfect, with no discoloration or pitting, and the plastic parts around them should look undamaged. Sometimes the connector is just loose, and snugging up the big silver nut on both sides will solve it. Not too tight, the plastic threads strip out easily.

Here is a Juiced battery with a damaged connector. The large 19ah juiced batteries are particularly prone to this. The connector has to be replaced, and it is usually a good idea to replace both the bike and battery sides at once.

The bike side is easy, just remove the plastic bracket that includes the battery locking mechanism from the bike, there is a vertical screw, visible in this picture, and another that is sometimes under a removable cover.  Loosen off the large silver nut on the connector, and press out the connector. Usually there is a way to unplug the wire attached to the connector from the motor controller.  If not, you will need to solder the new connector on, making sure to get the positive and negative leads on the correct pins, the back of the connector is marked for this. Red is usually +.

Note that the connector is keyed, and can only go into the hole in one orientation.  Be sure to get the connector fully seated in the bracket before carefully threading the nut on, and just snug the nut up, as overtightening it will strip the plastic threads. 

Now on to the battery:

For the battery side, first make sure that the battery is turned off.  This will disable the output of the battery management system (BMS) so that there is no voltage present at the connector.  Some batteries do not have this switch, and the output connector is always live.  If this is the case, you have to be extra careful to not let the two output wires touch during this repair. I always check for voltage with a DVM or  multimeter before proceeding.

With this Juiced battery the power switch can be disconnected to make the repair easier, just disconnect the black plastic JST inline connector with the four small wires.

Here the switch connector is removed.  Peel off the glue from the back of the output connector before removing the nut on the outside.

The old connector removed and ready to be replaced.

Here I have cut the red wire off, slipped on a piece of heat shrink tubing, and stripped back 1/4" of insulation. Push the heat shrink as far away from the end of the wire as possible, so that it doesn't shrink as you are soldering.  To minimize the possibility of a short circuit, never allow even the POSSIBILITY that the red and blue conductors can touch.  I do this by completing the repair one wire at a time, and insulating the connections as I go.

Here I am using a "helping hand" soldering aid to hold the wire in place for soldering.  Use a temperature controlled soldering iron, or a soldering gun, and flux core solder.

Make sure that the solder joint covers all of the wire, not just one side.  Try to do this a quickly as you can so as not to overheat the plastic connector.  Start with getting the solder into the wire, then the connector.

Heat shrink the first connection before moving on to the next to prevent the possibility of a short circuit..  The pins are close enough together that a drip of solder could bridge them when you are making the second connection. If there is no on/off switch on your battery, this would result in at the minimum a blown fuse, but possibly a fried BMS, or a battery fire.

I apply hot glue around the back of the connector to help prevent water ingress.

Don't forget to re attach the switch wires. I apply a bead of silicone on the Juiced batteries before re assembling the top cap, as there is no gasket to keep water out.  On the Hilleater batteries there is a gasket, so this is not necessary.  Wear gloves, and wipe off the excess as soon as the screws are tightened.  Its hard to get all the silicone off, but persistence pays off.  I have found that if you let the silicone dry, then try to cut or peel it off, it can come right out of the seam. Test the battery voltage output to make sure that you got the polarity correct before installing it back on the bike.


View Comments

David's interview on the 2pt5 podcast

A long rambling interview with Dr. Klaus Reichert from The2pt5 innovator podcast.https://the2pt5.net/david-elderton

Read More »

Other uses for your e-bike battery!

Power outage, camping, trolling motor, travelling with electronics, running a portable cooler, recharging your drone at the park?  All of these things can be done using your existing e-bike battery!  All you need is the correct plug to get the power out of the battery, and the equipment to deliver the correct voltage to your [...]

Read More »

Replacement battery packs for Juiced U500

The original Juiced Bike!  Back when they were called Juiced Riders, this was their first e-bike, and it remains popular today with a dedicated bunch of owners who appreciate the bikes rugged reliability and great utility.  The later models came with three battery capacities, 15, 23 and 32 ah.  The battery is no longer being made, [...]

Read More »

Electrafest Vancouver August 24th

Come see us at Electafest 2019! The Vancouver Electric Vehicle Association puts on this exhibition of everything electric every year in downtown Vancouver.  The location is the Roundhouse Community Center, at the foot of Davie St near False Creek.  Ride your bike, the location is just a block off of the sea wall, and there will be [...]

Read More »

Replacing a worn or faulty cassette freewheel tower on a Juiced CrossCurrent S or similar Bafang motor

Do you hear a clicking or cracking sound from your Juiced CCS rear wheel while pedalling?  Chances are you have a worn or defective cassette freewheel tower.  Sometimes this noise can be caused by a badly seated axle, so it is worth loosening the axle hardware, checking that the wheel is seated properly, and re [...]

Read More »

Charging your e-bike battery from another battery while you ride!

I recently did a 140km ride with some friends from the North End of Salt Spring Island, to Fulford on the South End, then Swartz Bay on the ferry, Victoria, and Langford via the Lochside Trail and the Galloping Goose bike trails, then all the way up to Cowichan River Provincial park on the Trans [...]

Read More »

Derailleur/drivetrain upgrade for Juiced CrossCurrent S, CC, CC AIR, CCX.

Got the upgrade bug?  Chain drops? We have something special for your CrossCurrent!  This is a killer drivetrain upgrade that includes a Shimano Deore derailleur with Shadow RD+ stabilizer.  This unit acts as a clutch, not allowing the chain to go slack and bounce off over bumps on 1X setups like the CCS.We have found [...]

Read More »

Energus Tiny BMS

We recently took on distribution of a new battery management system from a Lithuanian company called Energus. Small, Light, Safe, Simple All Lithium batteries have some sort of circuit that manages the voltages to make sure that the cells are not over charged or over discharged.  More sophisticated systems also balance the cells, so that each [...]

Read More »

Vancouver Bike Show, new hilleater bikes, new products

The Bike Show is always a sign thatSpring is coming!Go to the show website, and use coupon code CYCLING for $4.00 off your admission to the show.  We will be there showing:And introducing our own brand:We are super stoked to introduce hilleater e-bikes at the show. With this new brand we are emphasizing quality in [...]

Read More »